Fraser Techno
Plastics:
Modular sealing system for the passage of cables and pipes. The purpose of our product is to maintain the integrity of a firewall, bulkhead or deck through which cables and pipes pass.
MARINE HAWKE TRANSIT SYSTEM (Designed to be welded to decks and bulkheads)
CIVIL HAWKE TRANSIT SYSTEM (Designed to be built into concrete or bolted to walls and floors of buildings)
Made from an intumescent flame retardant elastomer coated on all surfaces with a silver loaded spray which is highly conductive and provides the excellent shielding ability. In addition, a layer of adhesive copper strip is applied around the block to aid conductivity
Disponible en 90 mm y 120 mm de tamaño.
Made from an intumescent flame retardant elastomer coated on all surfaces with a silver loaded spray which is highly conductive and provides the excellent shielding ability. In addition, a layer of adhesive copper strip is applied around the block to aid conductivity.
Stainless steel circular marine and civil frames for EMC transits.
Stainless steel rectangular marine and civil frames for EMC transits.
We provide the customer with accesories and tools to ocmplete and assist in the installation of the EMC Hawke Transit System.
The compression system in the plate that compresses and completes the seal.
Zero halogen intumescent polymer Tolerant Blocks and Filler Blocks coated in a silver-loaded paint to aid with conductivity.
Rectangular and circular Civil and Marine frames
Welding Fixing Tool (Ref.974) Tool is used to facilitate the welding process on a marine frame.
Our new silicone is used for sealing our HMFX range marine frames. The application method can be seen at the bottom of this page:
The 966 Mastic is necessary when frames HCX are to be bolted onto or into a structure, Hawke 966 Mastic should be place between the flange of the frame and the structure to ensure fire/smoke/gas/water tight seal, see installation instructions in product catalogue.
Hawke recommends 1 our Mastic Ref.966 for each 4 apertures.
The 967 Silicone Lubricant is use to aid the installation of blocks which are tightly fitted.
The silicone remains soft a low temperatures and will not dry out over long periods of time ensuring that future modifications to the transit will not be impeded.
Hawke recommends 1 our Lubricant Ref.967 for each 3 apertures.
Hawke Polystyrene Moulds are used to protect the inside of a frame during a casted installation in a floor or wall.
The purpose of this tool is to hold the position of the already installed blocks when the transit block installation is not completely done. This is also used to install the blocks (without cables).
Also, with this tool you can achieve a much greater comfort in a horizontal transit installation.
Hawke Backing Plates are used in conjuction with Hawke flanged frames to add finished appereance to an installation.
The 980 Puller tool is a re-usable piece of equipment which is used to aid extraction of compression system.
The re-usable compression tool is designed to apply compression to the system before placing the endpacker within the frame.
Reduces installation time by up to 50%.
Stayplates ensure the block in a Hawke rectangular system (tolerant and blank ones) are fixed in position after compression. For presure application in excess of 3.5 bar
Stayplates ensure the block in a Hawke rectangular system (tolerant and blank ones) are fixed in position after compression.
Certified for Marine applications.
Hawke HRST is a round sealing solution for a single/pipe passing through a wall or bulkhead/deck.
Each size of HRST frame can seal a large range of diameters without any onsite modifications.
More sizes under request, up to 350 mm OD.
Certified for both Civil and Marine applications.
The HRTO has been designed to be sealed using standard Hawke tolerant blocks, Hawke HRTO provide effectively sealing of cables and pipes through a circular aperture.
Hawke HRTO is supplied as an OPEN frame, so that it can be installed after laying the cables or pipes.
Hawke manufacture a range of blocks to suit the most popular waveguides sizes. Hawke wave guide insert blocks are used inserted in Standard HF Blocks.
Hawke Trefoil Insert Blocks: These blocks allow three single phase power cables to be sealed inside of the same cable block. *Available in 90mm and 120 mm size*
Hawke Especial Blocks: When Hawke Transit System Frames are penetrated by services that are shaped anything other than circular, eg. busbars, special cables, earthtraps, etc. Special EMC bocks can be manufacturer. Please contact our Sales Department for more information.
This enables a wide range of cable or pipe diameters to be accommodated by a compact range of tolerant block sizes.
Hawke tolerant blocks have five sealing faces that are displaced by the sealing process. This results in a tolerance of up to 4 mm for cable diameters.
Filler blocks are available in the same materials as the tolerant Blocks. They are used to fill spaces within the frame which are not required for services, thus allowing spare capacity for future requirements.
We provide the customer with accessories to complete and assist in the installation of the Hawke Transit System
The final element of the frame installation, this is inserted above the compression plate and the bolts tightened to seal the whole frame.
Designed to be sealed using standard Hawke tolerant blocks, Hawke round transit frames provide effectively sealing of cables and pipes through a circular aperture.
HRTO Certified for both Civil and Marine Aplications.
Zero halogen intumescent polymer colour coded Tolerant Blocks and Filler Blocks
Rectangular and circular frames for both civil and marine applications
Hawke H-DM is a cable sealing solution that guarantees an IP66 & IP67, specially designed for the sealing of electrical panel boards and cabinets.
Essential to ensure the integrity of computer and military communications.
Specially prepared to eliminate stray air bourn and cable screen signals/noise, apart from being certified as a fire, water and gas barrier.
